Food-grade used totes: one trip, one cargo, one very boring paper trail.
A food-grade used tote is not a used tote that somebody scrubbed hard. It is a container that has only ever held food, from a filler who wrote down what it was.
Quote: Food-Grade IBC Totes
Six things that have to be true before a tote is called food-grade here.
If any one of them fails, the unit drops to Grade A washed and gets priced accordingly. We would rather lose the margin than the trust.
- Exactly one prior cargo, and that cargo was food, beverage or a food ingredient
- A written declaration from the company that filled it, naming the product and the fill date
- No solvent, fuel, pesticide or unlisted chemical anywhere in the unit's history
- Triple rinse with potable water, logged with temperature and volume
- Bottle interior scoped on camera — no crazing, no stress whitening, no residue film
- New FDA-compliant gasket and cap, and a human nose signing off on the odour check
What food-grade stock has usually carried.
Most of our food-grade inventory comes from four places: syrup and concentrate houses, edible oil refiners, brine and vinegar producers, and dairy or beverage co-packers. Their containers are single-use by policy, which is exactly what makes them good second-life candidates.
These are the cargoes we see most often, and all of them rinse cleanly: maple syrup, apple and grape concentrate, high-fructose corn syrup, refined canola and soy oil, white vinegar, brine, molasses, liquid cane sugar, glycerine USP, citric acid solution and liquid egg.
- Syrup and concentrate — the cleanest category we handle
- Edible oils — hot wash required, never cold rinse
- Brine and vinegar — check the gasket, not the bottle
- Dairy — accepted only with a CIP record attached
What a potable triple rinse actually involves.
Drain and sump sweep
Residual product is pumped from the sump, measured and recorded. Food residue goes to a licensed renderer or digester, never to the drain.
Hot pre-wash
140–160 °F potable water with a food-safe alkaline detergent, recirculated through a rotating spray ball for a logged dwell time.
Three potable rinses
Three separate charges of potable water, each one drained completely. Conductivity of the third rinse is measured and recorded against the incoming water.
Pressure dry and scope
Filtered air dry, then a camera pass through the 6-inch port. Anything that looks like a film gets the unit sent back or downgraded.
Fittings and seals
New FDA-compliant EPDM gasket, new cap, valve exercised and inspected. Old gaskets are the single most common source of carried-over odour.
Odour and leak sign-off
A trained nose checks the headspace, then the unit is leak-tested and plated. Wash record and prior-contents sheet are stapled together and travel with the tote.
Food-grade used, or rebottled?
Food-grade used
- One documented prior food cargo
- Lower cost, faster from floor stock
- Full wash record and prior-contents sheet
- Ideal for the same cargo category it carried
- Faint cosmetic ghosting is possible
Rebottled
- Virgin interior, zero prior cargoes
- Costs more, takes a few days longer
- Cleanest option short of buying new
- Right call for potable water and pharma-adjacent work
- Still avoids ~71% of new-tote carbon
What auditors ask us.
Do you hold a food safety certification?
Our wash bay runs to a written SOP modelled on the Reusable Packaging Association's RPCC guidance and on 21 CFR 110 sanitation principles, and we keep wash records for seven years.
We are a container reconditioner, not a food processor, so we do not carry SQF or BRC certification. What we do carry is the full paper trail your own auditor needs: prior-contents declaration, wash parameters, rinse conductivity, scope result and leak test. See Standards & Certifications for the complete list.
Can you provide a resin or FDA compliance letter?
For rebottled units, yes — the bottle is new and the moulder's FDA-compliance statement comes with it.
For used food-grade units the original resin letter usually belongs to the first filler. We will chase it if the serial allows, but we never claim to have one we cannot produce.
What about allergens?
We record the prior cargo by name, so you can make your own allergen determination. Dairy, egg and tree-nut oils are flagged in our inventory system and will never be sold as generic food-grade stock without that flag being visible.
If your programme excludes a specific allergen entirely, tell us and we will quote rebottled instead. It is the only honest answer.
Is a vented or solid cap better for food?
Solid for anything you want to keep sterile and sealed in storage; vented if the cargo is being dispensed by gravity and you need air back in without pulling a vacuum on the bottle.
We fit whichever you specify and we will fit a tamper-evident band on request.
Baseline specifications for everything we handle.
| Container | Capacity | Footprint | Height | Tare | Gross at SG 1.0 | Per 53' trailer |
|---|---|---|---|---|---|---|
| Caged composite IBC | 275 gal / 1,040 L | 40 × 48 in | 46 in | 127 lb | 2,420 lb | 20 floor / 40 stacked |
| Caged composite IBC, XL | 275 gal / 1,040 L | 40 × 48 in | 53 in | 132 lb | 2,425 lb | 20 / 40 |
| Caged composite IBC | 330 gal / 1,250 L | 40 × 48 in | 53 in | 145 lb | 2,900 lb | 20 / 40 |
| Caged composite IBC | 350 gal / 1,325 L | 48 × 48 in | 52 in | 170 lb | 3,090 lb | 18 / 36 |
| Stainless bin, 304 | 350 gal / 1,325 L | 48 × 42 in | 55 in | 420 lb | 3,340 lb | 18 / — |
| Stainless bin, 316L | 500 gal / 1,893 L | 52 in dia. | 74 in | 580 lb | 4,750 lb | 14 / — |
| Poly drum, closed head | 55 gal / 208 L | 23 in dia. | 34.5 in | 22 lb | 480 lb | 80 on pallets |
| Steel drum, lined | 55 gal / 208 L | 22.5 in dia. | 33.5 in | 38 lb | 496 lb | 80 on pallets |
| Salvage overpack | 95 gal / 360 L | 28 in dia. | 40 in | 35 lb | 827 lb | 40 on pallets |
Figures are nominal and vary a little by moulder. Always multiply net volume by the actual specific gravity of your cargo before checking a forklift or racking rating.
The grading system, in one table.
| Grade | Prior cargo | Wash route | Clean index | Price index | Drops a grade if |
|---|---|---|---|---|---|
| A — Food | One, food only, documented | Route 3 potable triple rinse | 100 | 100 | More than one cargo, missing declaration, film on scope, odour fail |
| A — Rebottled | None — new bottle | New, unused | 98 | 86 | Cage fails node inspection or leak test |
| A — Washed | Non-hazardous industrial | Route 2 hot caustic | 92 | 74 | Ghosting remains, or cargo history unverifiable |
| B — Rinsed | Mixed industrial | Route 1 rinse | 72 | 52 | Structural repair, or odour a buyer would notice |
| C — Non-potable | Heavier residue, repaired | Route 1 rinse | 48 | 34 | Any crazing, any persistent bulge, failed leak test |
| D — Reclaim | Failed test or structure | Not resold | 16 | 9 | Not applicable — this is the floor |
Price index is relative to Grade A food at 100, not a quote. The absolute level moves with resin, scrap steel, freight rates and the agricultural season.
Bays, decks and the weather they live in.
Michigan concrete, a flatbed mid-load and the stacks these containers sit in between lives. No stock imagery anywhere on this site.
What arrives with the containers.
None of this is optional or chargeable. It is the difference between a reclaimed container and an anonymous second-hand one.
- A prior-contents sheet naming the product, the fill date and the company that filled it
- Four photographs of the actual unit plus an image of the cage stamp
- The grade assigned, and the published criteria that grade commits us to
- A wash record where the unit went through Route 2, 3 or 4, with temperature, dwell, rinse count and final rinse conductivity
- A leak test record for every Grade A and Grade B unit: method, pressure, hold time and measured decay
- The UN plate photograph and periodic test dates where the unit is marked
- A component list naming gasket material, valve type and cap type
- The cage passport ID, so the whole service history can be reissued later
- An allergen flag where a prior food cargo included dairy, egg or tree-nut oils
- A standing take-back offer: when you are finished, we collect and pay
Cargo weight by specific gravity.
| Cargo | SG | 275 gal net | 275 gal gross | 330 gal gross | Notes |
|---|---|---|---|---|---|
| Ethanol, 190 proof | 0.81 | 1,858 lb | 1,985 lb | 2,375 lb | Flammable — conductive container required |
| Used motor oil | 0.89 | 2,042 lb | 2,169 lb | 2,595 lb | Warm before pumping in winter |
| Canola oil, refined | 0.92 | 2,110 lb | 2,237 lb | 2,678 lb | Hot wash route only |
| Water | 1.00 | 2,294 lb | 2,421 lb | 2,898 lb | The baseline for everything |
| Propylene glycol | 1.04 | 2,386 lb | 2,513 lb | 3,008 lb | Commonest tote cargo in the Midwest |
| Urea solution 32.5% | 1.09 | 2,500 lb | 2,627 lb | 3,145 lb | Freezes at 12 °F |
| Hydrochloric acid 35% | 1.18 | 2,707 lb | 2,834 lb | 3,393 lb | Viton gaskets, never EPDM |
| Liquid cane sugar | 1.33 | 3,051 lb | 3,178 lb | 3,804 lb | Near the density limit for a 330 |
| Ferric chloride 40% | 1.42 | 3,258 lb | 3,385 lb | 4,052 lb | Stains HDPE permanently |
| Caustic soda 50% | 1.53 | 3,510 lb | 3,637 lb | 4,355 lb | 275 only; check the forklift rating |
| Sulphuric acid 93% | 1.83 | 4,198 lb | 4,325 lb | 5,208 lb | Steel or stainless service, not poly |
Gross figures include tare of 127 lb for a 275 and 145 lb for a 330 on steel pallets. The maximum net mass on the UN plate is a separate and binding limit.
Buying questions, answered at length.
How do I know the grade is honest?
Because the disqualifiers are published. A Grade A food unit drops to Grade A washed if there is more than one prior cargo, if the declaration is missing, if third-rinse conductivity is out of tolerance, if the scope shows film, or if the odour check fails.
Ask any supplier what would disqualify a unit from the grade they just sold you. A supplier who cannot answer immediately does not have a grading system.
What happens if a unit is not as described?
We replace it, re-grade and refund the difference, or collect it and refund in full — your choice, not ours.
We have refunded four units in the last three years. All four were our grading error, and all four customers still buy from us.
Do you substitute units without telling me?
No. Container reconditioning depends on inspection outcomes we cannot fully predict, so units occasionally fail during processing.
When that happens we tell you immediately and offer the nearest available alternative, rather than quietly shipping something different and hoping the photographs were not studied.
Can I specify valve, cap and gasket?
All three, on any grade. If you name the cargo we will specify them for you rather than making you learn three buttress thread standards and six camlock types.
The most expensive eleven-dollar mistake in this industry is EPDM in aromatic service. It swells, extrudes out of the joint and fails without warning.
What payment terms do you offer?
Pro forma for a first order, net 30 on account once established, and purchase orders for public buyers as standard.
Quotes are valid thirty days. Beyond that we refresh rather than honour a stale number, in either direction — this market moves with resin, scrap steel and the agricultural season.
Will you tell me to buy something cheaper?
Frequently, and it is commitment seven of our circular pledge: every new-container quote includes the nearest reclaimed option with the carbon difference written out.
We also steer dense cargo from 330s to 275s, site water from Grade A to Grade C, and drinking water away from used bottles entirely.
Eight mistakes we watch customers make, repeatedly.
None of these are stupid. All of them are expensive, and every one of them has happened to somebody competent in the last twelve months.
1. Multiplying volume by 8.34 and forgetting specific gravity
A 275-gallon tote of 50% caustic soda grosses 3,637 lb, not 2,420. Forklift capacity ratings, racking beams and warehouse floors all care about the real number. This is the single most common serious miscalculation in liquid handling.
2. Buying Grade A washed for site water
Cosmetic condition has no effect on how well a container holds water for dust suppression. Grade C costs a third as much and lasts exactly as long under that treatment. Roughly half the customers who ask for Grade A are paying for appearance they do not need.
3. Fitting a vented cap for storage
A vented cap is a dispensing device. Left on a stored container it pumps moist air in all winter, and we have opened totes in March with half a litre of condensate sitting on top of the cargo. Solid cap in storage and transit; vent at the point of use.
4. Filling to the brim before a freeze
Water expands about nine percent on freezing and an HDPE bottle will crack at the lower corner near the sump almost every time. Fill water-based cargo to 85% and store where the unit can drain.
5. Reusing the gasket
The cheapest component in the assembly and the most common source of carried-over odour and cross-contamination. Gaskets take a compression set, harden, and hold prior cargo in the elastomer.
6. Ordering twenty-two units
A 53-foot trailer holds twenty. Twenty-two pays for two trailers to move two containers. Tell us if your number is flexible and we will tell you which way to move it.
7. Forcing a buttress thread
S60×6, S70×6 and S75×6 will each start on the others and then bind. Two turns and a stop means the wrong standard, and forcing it crazes the bottle neck permanently.
8. Storing translucent bottles outdoors
UV plus freeze-thaw cycling is what finally kills HDPE. We have measured 10% wall loss on the south face of bottles after five years in the open, with the shadow pattern of the cage printed onto the plastic. Black UV-stabilised bottles outlast translucent ones by three to four times outdoors.
Threads, fittings and gaskets.
| Designation | Size | Where it appears | Mates with | Gasket |
|---|---|---|---|---|
| S60×6 | 60 mm buttress | Schütz, Werit, most European bottles | S60×6 adapters, GHT reducer | Flat EPDM or Viton |
| S70×6 | 70 mm buttress | Mauser and many North American bottles | S70×6 to 2 in camlock | Flat EPDM or Viton |
| S75×6 | 75 mm buttress | Older Schütz, some Greif | S75×6 to S60×6 reducer | Flat EPDM |
| 6 in coarse | ~150 mm | Top fill port, near universal | Vented or solid cap, bung insert | Flat gasket or liner seal |
| 2 in NPT | Tapered pipe | Valve outlets after adapter | Camlock type C or D | PTFE tape on thread |
| Camlock type C | 2 in coupler | Hose end, female | Type A or F | Internal seal ring |
| GHT 3/4 in | Garden hose | Irrigation, rain harvesting | GHT to S60×6 | Hose washer |
| Tri-clamp 2 in | Sanitary ferrule | Stainless bins | Tri-clamp ferrule | Silicone or EPDM |
Buttress threads are asymmetric and will start on an adjacent standard before binding. Two turns and a stop means it is the wrong thread — do not force it, you will craze the bottle neck.
Technical questions about the containers themselves.
How do I get the last of the product out?
Level the container first, then tilt it forward with a 50 mm block under the rear feet. The sump works because it is the lowest point, and two degrees out of level moves the lowest point to the back wall.
For viscous cargo, warm it to 100–120 °F with a thermostatic jacket — never above about 140 °F on HDPE. For high-value product, a dip tube to the sump with a diaphragm pump recovers more than gravity does.
What does the UN marking mean?
Taking 31HA1/Y/03 25/USA/M5678/1040/127 as an example: 31HA1 is the design type (composite IBC for liquids, plastic inner, rigid steel outer, with structural equipment); Y is the packing group capability (II and III); 03 25 is March 2025; USA is the approving authority; M5678 is the manufacturer code; 1040 is the stacking test load in kg; 127 is the tare.
A separate stamped date records the last periodic test, and that is the one that determines whether the container may be offered for regulated transport today.
Should I buy translucent or black bottles?
Translucent indoors, black outdoors, every time. Translucent gives you level visibility for free; black gives you three to four times the outdoor life.
We measured twelve translucent units pulled after four to six years outdoors: south walls 0.21 mm thinner than north walls on the same unit, chalking on every south and west face, and coupons that snapped like a biscuit when folded.
How do I tell how old a container is?
Three independent sources, and they do not always agree. The UN plate carries a date of manufacture for the assembly. The bottle has a moulded date wheel — a clock face with the month and a two-digit year. The cage usually has a stamped week-and-year code on the lower rail, right-hand side facing the outlet.
Bottle newer than plate means a rebottle. Plate newer than cage stamp means a recertification. We list all three separately on every unit and say why when they conflict.
What is crazing and how do I spot it?
A network of microscopic voids in stressed polymer — the immediate ancestor of a crack, and the reason most reclaimed bottles are eventually scrapped.
It is nearly invisible head-on. Put a light behind the bottle wall, get your eye within fifteen degrees of the surface and look along it: crazed regions light up as a silvery sheen that moves as you shift your head. Check all four lower corners and the sump transition. Thirty seconds per unit.
Is a bulged bottle still usable?
Empty it and look again. If the bulge goes, you have an overfilling or thermal problem and the container is fine. If it remains when empty, that is creep — permanent deformation under sustained load — and the unit should not be refilled.
A bulge that includes the top of the bottle rather than the bottom means gas generation, which is a hazard rather than a defect. Vent slowly from the side with the cap pointed away.
The pages our own staff keep open.
Chemical compatibility, container by gasket.
| Cargo | HDPE bottle | EPDM | Viton | PTFE | Note |
|---|---|---|---|---|---|
| Water, potable | Excellent | Excellent | Excellent | Excellent | Rebottled or Grade A food only |
| Sodium hypochlorite 12.5% | Good | Fair | Good | Excellent | Vent — the cargo off-gasses and will bulge a sealed bottle |
| Caustic soda 50% | Excellent | Excellent | Good | Excellent | SG 1.53 — 275 gal only, check the forklift plate |
| Sulphuric acid 93% | Not suitable | Not suitable | Fair | Excellent | Lined steel or stainless service, never poly |
| Hydrochloric acid 35% | Good | Not suitable | Excellent | Excellent | Viton only; HCl destroys EPDM in weeks |
| Nitric acid 10% | Fair | Not suitable | Good | Excellent | Oxidiser — embrittles HDPE over months |
| Phosphoric acid 75% | Good | Fair | Good | Excellent | Common fertiliser intermediate |
| Propylene glycol | Excellent | Excellent | Excellent | Excellent | The most-handled tote cargo in the Midwest |
| Ethylene glycol | Excellent | Excellent | Excellent | Excellent | Label clearly — it is routinely confused with PG |
| Ethanol, 190 proof | Good | Fair | Excellent | Excellent | Flammable — conductive container and bonding required |
| Methanol | Good | Fair | Excellent | Excellent | Permeates slowly through HDPE; not for long storage |
| Mineral oil, white | Excellent | Not suitable | Excellent | Excellent | EPDM swells in hydrocarbons |
| Used motor oil | Excellent | Not suitable | Excellent | Excellent | Warm to 60 °F before pumping in winter |
| Diesel and heating oil | Good | Not suitable | Excellent | Excellent | Check local rules before storing fuel in an IBC |
| Vegetable and canola oil | Excellent | Good | Excellent | Excellent | Hot wash route afterwards or it polymerises |
| Urea solution 32.5% (DEF) | Excellent | Excellent | Excellent | Excellent | Freezes at 12 °F, expands, then recovers |
| Liquid fertiliser 28-0-0 | Excellent | Excellent | Excellent | Excellent | Stains the bottle; does not harm it |
| Ferric chloride 40% | Excellent | Not suitable | Excellent | Excellent | Permanent orange staining — cosmetic only |
| Hydrogen peroxide 35% | Fair | Not suitable | Good | Excellent | Vented cap mandatory; dedicated bottle, never reused |
| Acetic acid 80% | Good | Fair | Good | Excellent | Odour carries over — dedicate the unit |
| Latex paint and coatings | Excellent | Good | Excellent | Excellent | Never let it dry inside; a cured film is unremovable |
| Toluene, xylene, MEK | Not suitable | Not suitable | Good | Excellent | Aromatic solvents swell and soften HDPE |
| Isocyanates and polyols | Refused | Refused | Refused | Refused | On our published exclusion list — they cure |
| Firefighting foam concentrate | Refused | Refused | Refused | Refused | PFAS risk; we will not take it at any price |
Ratings are for ambient-temperature storage in a reclaimed container, not for pressurised or heated service. Every 20 °F above 100 °F roughly halves the service life of the rating. When the cargo is not on this list, send us the SDS and we will tell you what we would and would not put it in.
The anatomy of a caged tote, part by part.
A 275-gallon caged IBC looks like one object and is actually five, each with a different lifespan, a different failure mode and a different second-hand value. Knowing which part you are buying is most of what separates a good purchase from an expensive one.
The inner bottle
Blow-moulded HDPE, 42 lb, nominal wall around 2 mm with deliberate thickening at the corners and the sump. It carries the cargo and nothing else. It is the part that ages: UV takes the surface, freeze-thaw cycling takes the corners, aromatic solvents soften the wall, and chemical stress plus mechanical stress together produce crazing. A bottle in indoor service with a compatible cargo will outlive the person who bought it. The same bottle in a Michigan yard, translucent, filled to the brim in November, has about five years.
The steel cage
Tubular galvanised steel, 55 lb, 44 to 54 welded nodes depending on the moulder. It takes every load the bottle cannot: stacking, strapping, forklift abuse, the hydrostatic push of a full bottle against its own walls. Cages outlast bottles roughly three to one, which is why rebottling exists as a trade at all. The failure modes are cracked nodes, a diagonal pushed out of square by impact, and red rust bleeding through a breached galvanising layer at a weld.
The base
Steel, composite, hybrid or timber, 22 to 44 lb. It decides how the unit can be handled and whether it can leave the country. Four-way entry and pallet-jack access are not universal, and a timber base without an ISPM 15 heat-treatment stamp will be stopped at a border. The welds attaching the cage to a steel base are a specific inspection point because a failed base weld makes the whole unit unstable under load with no other visible symptom.
The closures
A 6-inch top cap, a 2-inch discharge valve, the adapter stack at the outlet, and the gaskets. Together they weigh a few pounds, cost a fraction of the assembly, and cause most of the complaints: weeping valves, carried-over odour, cross-threaded adapters, vented caps left on in storage. We replace the valve, cap and gasket on every Grade A unit for exactly this reason — it is the cheapest possible insurance against the most common possible problem.
The markings
The UN plate, the cage stamp, the moulder's date wheel inside the bottle skirt. These are the unit's identity. The plate decides whether it can carry a regulated cargo and until when; the cage stamp is how we can reissue a seven-year service history years after the unit left the yard. A unit with an illegible plate is not scrap — it is a perfectly good container that has lost its licence, and it is priced accordingly.
If you only remember one thing: you are buying a bottle with a date on it, bolted into a cage that will outlive it, with hardware that should be new. Price the bottle, inspect the cage, insist on the hardware.
Valves, caps and how each one fails.
| Component | Typical material | Service | How it fails | Our policy |
|---|---|---|---|---|
| Butterfly valve, 2 in | HDPE body, EPDM seat | General liquid | Seat takes a set and weeps after long storage open | Replaced on every Grade A unit |
| Ball valve, 2 in | PP body, PTFE seat | Chemical, viscous | Handle shears; ball scores on grit | Function-tested, replaced if scored |
| Camlock adapter, type A/F | Aluminium or poly | Hose connection | Thread galls, cam arms bend | Supplied new where ordered |
| Dust cap, type DC | Poly | Transport closure | Lost in transit, never replaced | Fitted before despatch, always |
| Screw cap, 6 in solid | HDPE | Storage and transit | Gasket compression set; overtightening crazes the neck | New cap and new gasket on Grade A |
| Screw cap, 6 in vented | HDPE with one-way vent | Dispensing only | Pumps moist air in during storage | Supplied only when asked for, with a warning |
| Bung insert, S60×6 / S70×6 | HDPE | Adapter seat | Cross-threaded by force | Checked for thread damage under a light |
| Tamper seal | Nylon or wire | Evidence of opening | Cut and discarded, then nobody can tell | Fitted on all food-grade despatches |
| Breather valve | PP with PTFE disc | Off-gassing cargo | Blocked by crystallisation | Recommended for hypochlorite and peroxide |
| Internal dip tube | HDPE | Pump suction | Trapped residue; blocks a wash route | Removed and washed separately, or discarded |
Gaskets are the cheapest component in the assembly and the single most common cause of carried-over odour. We do not reuse them on any Grade A or Grade B unit, and we will not sell you a food-grade tote with its original gasket in it.
Stock waiting on inspection.
The twenty-two point intake inspection.
| # | Check | Pass criterion | Fail consequence |
|---|---|---|---|
| 01 | Prior-contents declaration present | Named product, filler, fill date | Quarantine bay until named, or refused |
| 02 | Cargo against exclusion list | Not on the published list | Refused at the gate, load turned away |
| 03 | Residual heel volume | Under 1 gal, drainable | Charged back, or refused above 5 gal |
| 04 | Odour, cap off, ambient | No detectable cargo odour after rinse | Drops to Grade C or reclaim |
| 05 | Bottle wall thickness, four points | Within 15% of nominal | Reclaim |
| 06 | Crazing under raking light | No branching cracks anywhere | Reclaim — crazing never improves |
| 07 | Stress whitening at the sump | None, or faint and non-progressive | Grade C maximum |
| 08 | Bulge, measured at mid-wall | Under 6 mm from datum | Grade C or reclaim by severity |
| 09 | UV chalking on the sun face | Surface only, no wall loss | Grade C for outdoor-only use |
| 10 | Neck thread condition | Clean start, two full turns by hand | Rebottle or reclaim |
| 11 | Internal scope, 360° | No film, no deposit, no shadowing | Re-wash, then regrade |
| 12 | Weld node count and integrity | 44–54 nodes, none cracked | Cage repair or scrap the cage |
| 13 | Cage geometry, diagonal check | Within 10 mm across diagonals | Press back or scrap |
| 14 | Galvanising condition | No red rust through the zinc | Grade C, or wire-brush and paint |
| 15 | Base weld to pallet | All welds sound under load | Scrap the base, transplant the bottle |
| 16 | Pallet type and ISPM stamp | Matches order; stamp present if export | Re-sorted to the correct bay |
| 17 | UN plate legible | All fields readable, dates in date | Sold as non-regulated service only |
| 18 | Leak test, pneumatic decay | Under 1 kPa loss in 10 min at test pressure | Repair and retest, or reclaim |
| 19 | Valve function, full travel | Opens, closes, seals dry | Valve replaced |
| 20 | Gasket condition | Not reused on A or B — always new | New gasket fitted |
| 21 | Photographs, four plus cage stamp | In focus, bay number visible | Reshot before despatch |
| 22 | Passport record written | Cage ID, grade, route, dates, operator | Unit does not leave the yard |
Checks 05 to 09 are where most units lose a grade, and they are all condition of the bottle rather than cleanliness. A container can be surgically clean inside and still be Grade C because of what five Michigan winters did to the outside.
Specification questions, in detail.
Which gasket do I need?
EPDM for water, glycols, caustics, fertilisers and most food products. Viton for acids, hydrocarbons, solvents and anything aromatic. PTFE for aggressive oxidisers and where nothing else is rated.
The two expensive errors are EPDM in hydrochloric acid, where it is destroyed in weeks, and EPDM in hydrocarbons, where it swells. If you tell us the cargo we specify the elastomer, and it is on the component list that ships with the unit.
What does the stacking figure on the plate actually mean?
It is the permissible superimposed load: how much mass may sit on top of that container. It assumes normal temperature, level ground and an evenly distributed load, and a zero means do not stack even empty.
The real-world caveat is temperature. Above 100 °F derate by half; above 120 °F do not stack at all. HDPE creeps under sustained load and heat accelerates it, so a stack that was fine in April can deform in July without anything else changing.
How long does an HDPE bottle actually last?
Indoors with a compatible cargo, longer than the business using it — we regularly handle bottles over twenty years old that pass every test. Outdoors, translucent, filled to the brim through Michigan winters: about five years.
What kills them is the combination of UV, freeze-thaw cycling and chemical stress acting together. Any one is survivable. All three together produce crazing, and crazing is the one condition with no path back.
Is stress whitening the same as crazing?
No, and the distinction is worth money. Stress whitening is localised opacity where the polymer has been strained, almost always a forklift impact near the sump. It looks alarming and is often not a failure.
Crazing is a network of fine branching cracks from chemical and mechanical stress together. It is an absolute disqualifier, it never improves, and the test is a raking light at a shallow angle across the surface. If you can see branching, the bottle is finished — though the cage and base are still worth money.
Can a cage be reused with a new bottle?
Yes, and that is what rebottling is: a new blow-moulded HDPE bottle fitted into an inspected cage and base. Cages outlast bottles about three to one, which is why the trade exists.
The cage goes through the same inspection as everything else first — 44 to 54 weld nodes counted individually, diagonals measured, base welds loaded, galvanising checked at the welds. We fitted 4,118 new bottles in 2025. Bench turnaround on contract work is 48 hours.
Do you have 350 and 500 gallon containers?
Yes, as stainless bins rather than caged composites. A 350-gallon square 304 bin is 48 × 42 inches and 55 inches tall with a 420 lb tare; a 500-gallon cylindrical 316L is 52 inches in diameter, 74 tall, 580 lb.
They are the right answer for aggressive acids above SG 1.6, for hot cargo, and for anything where you want a container that will outlive several poly ones. They do not stack, and the trailer count drops to fourteen for the 500s.
What is the heaviest cargo you would put in a reclaimed poly tote?
In practice, 50% caustic soda at SG 1.53 in a 275 — which grosses 3,637 lb — is about where we stop being comfortable, and we check the customer's forklift rating before quoting it.
Sulphuric acid at 93% and SG 1.83 we will not put in poly at all; that is steel or stainless service. The limiting factor is rarely the bottle's burst strength and almost always everything underneath it: forks, beams, floors.
New container against reclaimed, without the sales pitch.
There are jobs where a new container is the right answer. We would rather say so than sell you the wrong thing and collect it back in a year.
Buy new when
- The cargo is a regulated Packing Group I material
- You need a specific design type, pressure rating or exotic liner nobody reclaims
- Your customer's audit requires virgin packaging in writing
- The product carries an allergen claim and rebottled will not satisfy the auditor
- You need five hundred identical units with identical plate dates on one date
- The container is part of a sealed, validated single-use process
Buy reclaimed when
- The cargo is water, glycol, fertiliser, a utility liquid or an unregulated industrial product
- A documented prior cargo and a published wash route satisfy your requirement
- You want the same container at 30 to 60 percent of the new price
- You want the impact figure, and the methodology behind it, in your own reporting
- You need units this week rather than on a moulder's lead time
- You want rebottled: a new HDPE bottle in an inspected cage, which is new where it touches the cargo
What actually moves the price of a reclaimed tote.
| Driver | Direction | Typical effect | Can you control it? |
|---|---|---|---|
| Grade | A costs more than C | Up to 3× across the range | Yes — most buyers over-specify |
| Wash route required | Route 3 over Route 1 | +18 to +30% | Yes, by naming the real end use |
| New bottle (rebottled) | Up | +40 to +60% over washed | Yes — only food and potable truly need it |
| Quantity against trailer fit | 20, 40, 60 are efficient | ±15% on delivered cost | Yes, and this is the easiest saving |
| Freight zone and lane | Lane beats distance | ±40% on delivered cost | Partly — ask which day we run your lane |
| Season | B and C peak in spring | +15 to +20% March–May | Yes, if your timing is flexible |
| Pallet base specified | Steel or composite over timber | +4 to +20% on the base | Yes |
| New valve and cap | Up | Fixed per unit | Yes — reconditioned hardware is an option on C |
| UN plate in date | Up | +8 to +12% | Only if your cargo is regulated |
| Resin and scrap steel index | Both directions | Moves the whole market | No |
| Diesel | Up with fuel | Freight line only | No |
| Take-back credit on your old units | Down, against the invoice | Offsets part of the order | Yes — ask before you dispose |
We quote containers and freight as separate lines, because a single delivered number hides which of these twelve things you are actually paying for. If a quote you are comparing does not split them, ask.
Lead times, honestly, by grade and quantity.
| Order | Grade A food | Grade A washed | Grade B | Grade C | Rebottled |
|---|---|---|---|---|---|
| 1–4 units | 2–4 days | Same or next day | Same or next day | Same day | 3–5 days |
| 5–19 units | 3–6 days | 1–3 days | 1–2 days | Same or next day | 5–8 days |
| 20 (one trailer) | 5–8 days | 2–4 days | 2–3 days | 1–2 days | 7–10 days |
| 21–60 | 1–2 weeks | 4–8 days | 3–6 days | 2–4 days | 2–3 weeks |
| 61–200 | 2–4 weeks | 1–2 weeks | 1–2 weeks | 4–8 days | 4–6 weeks |
| Over 200 or scheduled programme | By schedule | By schedule | By schedule | By schedule | By schedule |
Grade A food is slower than everything else because Route 3 runs at 55 units a day against 90 on the other routes, and because the paperwork is checked twice. In March to May, add roughly a week to Grade B and C — that is the agricultural pull, and it is the most predictable thing in this market.
The twelve-minute check to run when the truck arrives.
Do this before the driver leaves, with the paperwork in your hand. It takes about a minute a unit on a small order and it is the only moment when a problem costs you nothing to raise.
Before anything comes off the trailer
- Count the units and compare against the bill of lading, not against memory.
- Photograph the load in the trailer, from the door, before the first unit moves. This single photograph settles almost every freight-damage dispute.
- Look along the top of the load for crushed cages, which is what a stacked load that shifted looks like.
On each unit, as it lands
- Read the cage stamp and check it against the photographs you were sent. Same unit, or not.
- Cap on and tight? A missing or loose top cap means the unit travelled open.
- Dust cap on the discharge? If it is missing, the valve has been exposed to road spray.
- Open and close the valve through full travel, then wipe it dry and watch it for a minute.
- Look along the lower corners and the sump under a raking light for whitening or cracks.
- Check the diagonals by eye: a cage out of square has been hit.
- Look at the base welds, all four corners, with the unit lifted a couple of inches.
- Read the UN plate and confirm the periodic dates match what you ordered, if your cargo is regulated.
On the paperwork, before you sign
- Prior-contents sheet present, naming product, filler and fill date.
- Grade stated, and the wash record attached if it was Route 2, 3 or 4.
- Leak test record present for every A and B unit, with actual numbers on it.
- Gasket material named on the component list, and matching your cargo.
If something is wrong
Note it on the delivery paperwork before signing and photograph it with the unit's cage stamp in the same frame. Then email us. With a cage ID and a photograph we can pull the intake record, the wash log, the leak test and the despatch photographs within minutes, and the conversation is about facts rather than recollection. Units that are not as described come back on our freight, not yours.
Price, quantity and when to buy.
Why are containers and freight on separate lines?
Because a single delivered number hides which of a dozen variables you are paying for, and makes comparing two quotes impossible. Grade, wash route, hardware, pallet base, plate status, lane, season and quantity all move independently.
It also means that when you come back in six months, we can tell you whether the price moved because resin moved or because diesel moved. If a quote you are comparing does not split them, ask — the answer tells you something either way.
Is there a volume price, and at what point?
The real breaks are at trailer boundaries — twenty, forty, sixty — because that is where freight per unit steps down rather than drifting. Container pricing softens with volume too, but less than people expect, because the cost is dominated by wash bay time and bay time does not get cheaper in bulk.
Scheduled programmes are a different conversation: if you need forty units a month every month, we can hold stock and plan wash capacity around you, and that is worth more to both of us than a one-off discount.
When in the year should I buy?
Late summer for Grade B and C, if your timing is flexible. March to May is the agricultural pull and it puts fifteen to twenty percent on those grades while leaving Grade A almost untouched.
June to August is the softest point of the year on the grades that actually move seasonally. Buying Grade B in August rather than April is the single easiest saving available in this market, and it costs you nothing but storage space.
Do you charge for the documentation?
No, and we would rather you did not ask it as a question, because a supplier who charges for a wash record is telling you the record is a product rather than a byproduct of the process.
The prior-contents sheet, wash record, leak test, plate photograph, component list and passport ID come with every order. The vendor pack — W-9, insurance certificate, wash SOP, discharge permit, methodology, and the signed statement of what we are not certified for — arrives in one email, usually inside the hour.
What is the most expensive mistake buyers make?
Specific gravity, by a wide margin, and it is never the container that fails. A 275-gallon tote of 50% caustic soda grosses 3,637 lb rather than 2,420. What fails is a forklift, a racking beam or a warehouse floor rated for the water figure.
Second place is buying Grade A for a job Grade C does. Third is ordering twenty-two units. All three cost more than the containers did.
Can I rent instead of buying?
We do not rent, and the arithmetic is why: a reclaimed tote costs a fraction of a new one and holds residual take-back value at end of life, so for almost every use case buying and selling back beats renting.
Where people genuinely want rental, what they usually want is a scheduled programme — units delivered when needed, collected when finished, credited on return. That we do, and it behaves like rental on your cash flow without the premium.
Why is one supplier's Grade A cheaper than another's?
Because 'Grade A' is not a standard. It is whatever each supplier means by it, and the only way to compare two of them is to ask what would disqualify a unit from that grade and what records come with it.
A washed unit with one documented food cargo, a logged Route 3 wash, a new gasket and a leak test with numbers on it is a different object from a rinsed unit that looked clean. Both get called Grade A. One of them costs forty percent more and is worth it; the other is a gamble priced like a certainty.
Pallet bases compared, including the one you cannot export.
| Base | Tare | Forklift | Pallet jack | Export | Washdown | Typical price index |
|---|---|---|---|---|---|---|
| Steel pallet | 31 lb | Four-way | Yes | Yes | Excellent | 100 |
| Composite / plastic pallet | 26 lb | Four-way | Yes | Yes | Excellent | 96 |
| Steel-and-wood hybrid | 38 lb | Four-way | Yes | ISPM 15 heat-treat stamp required | Poor — timber absorbs | 88 |
| Full timber pallet | 44 lb | Four-way | Marginal | ISPM 15 stamp required | Poor | 80 |
| Rigid plastic skid, two-way | 22 lb | Two-way only | No | Yes | Excellent | 84 |
If the container is leaving the country, a timber base needs the ISPM 15 heat treatment stamp or it will be stopped. We sort for base type at intake, so ask for steel or composite at quote stage rather than discovering the problem at the dock.
Temperature limits and the derating nobody mentions.
| Temperature | HDPE bottle | Steel cage | Gasket | Stacking allowed | Practical effect |
|---|---|---|---|---|---|
| Below −20 °F | Brittle | Fine | Hardened | No | Impact cracking at the sump corner; do not forklift a cold full tote hard |
| −20 to 32 °F | Serviceable | Fine | Stiff | Yes, derate 25% | Water-based cargo freezing; fill to 85% only |
| 32 to 100 °F | Full rating | Full rating | Full rating | Yes, full | Normal service window — every published figure assumes this |
| 100 to 120 °F | Softening | Fine | Fine | Derate 50% | Visible bulge in a full tote standing in July sun |
| 120 to 140 °F | Marginal | Fine | Check cargo | No | Creep accelerates; never stack, never rack |
| 140 to 160 °F | Short excursion only | Fine | EPDM limit | No | Wash bay territory — empty units only |
| Above 160 °F | Not suitable | Fine | PTFE only | No | Permanent deformation; the unit leaves as Grade D |
Heat-affected HDPE does not recover its original wall strength when it cools. This is why anything that has been near a fire is refused at our gate regardless of how it looks.
The fourteen fields that make a quote unambiguous.
Send us these and the quote comes back the same day, correct. Leave half of them out and we start with questions, which costs you a day.
- Cargo, by product name — and the SDS if it is anything unusual
- Specific gravity, or let us look it up, but somebody must
- End use: storage, transport, dispensing, fabrication, standby
- Quantity, and whether it is flexible — this is where trailer arithmetic saves you money
- Size: 275, 330 or 350 gallons, or tell us the volume and let us pick
- Grade, or better, let us recommend one from the cargo and end use
- Gasket requirement, if your cargo has one — EPDM, Viton or PTFE
- Valve and cap: standard, new, vented or specified
- Pallet base: steel, composite or any — and whether it is leaving the country
- Whether the UN plate must be legible and in date
- Delivery zip code, and whether you have a dock or need a lift gate
- Delivery window, and whether it is hard or indicative
- Documentation you need, and the format your auditor wants it in
- Whether you have old units to go back on the same visit
Ten questions that tell you what a supplier actually is.
Ask these of us too. A supplier who answers all ten without hesitation is running a real process; one who cannot answer three of them is reselling whatever came in on the last truck.
- What was in this specific unit, and who filled it? Hesitation here is the only red flag that matters.
- What would disqualify this unit from the grade you just sold me? No published disqualifiers means no grading system.
- Can I see photographs of the actual units before I pay, with the cage stamp visible?
- What did the third rinse read, and what did your supply water read that morning?
- Is the gasket new? If not, why am I paying for a clean container with the old cargo's elastomer in it?
- What method, pressure and hold time was the leak test, and what decay did it measure?
- Are the periodic test dates on the plate in date, and will you photograph the plate?
- Are containers and freight quoted as separate lines?
- Will you put in writing what you are not certified for?
- Will you take these back at end of life, and will you pay for them?
Symptom, cause, what to do about it.
| Symptom | Most likely cause | Check first | Fix |
|---|---|---|---|
| Weeping at the valve when closed | Seat compression set from long open storage | Close fully, wipe dry, watch 10 min | Replace the valve; store closed in future |
| Drip from under the valve body | Flange gasket, not the valve | Feel behind the valve for wet | Pull the valve, new flange gasket |
| Cargo odour in a clean tote | Original gasket retained, or cap gasket | Smell the gasket itself, off the unit | New gasket; re-rinse; air with the cap off |
| Bottle bulging at mid-wall | Overfill, heat, or off-gassing cargo | Cargo SDS for gas generation; ambient temp | Vented cap at point of use; reduce fill to 85% |
| Condensate on top of the cargo | Vented cap left on in storage | Which cap is fitted | Solid cap for storage; vent only when dispensing |
| Crack at the lower corner | Water-based cargo froze at full fill | Fill level history | Unit is finished — we will take it back for reclaim |
| White cloudy patch at the sump | Stress whitening from forklift impact | Raking light for branching cracks | Monitor; no crazing means serviceable, Grade C |
| Fine branching cracks | Crazing, from chemical stress or UV | Any raking light at a shallow angle | Retire the bottle; the cage and base are reusable |
| Flow stops mid-discharge | Vacuum lock — no air in | Crack the top cap and listen | Vent while dispensing, always |
| Slow flow on a cold morning | Cargo viscosity, not a blockage | Cargo temperature against its SDS | Warm the product; never heat the bottle directly |
| Adapter binds after two turns | Wrong buttress standard | Compare S60×6 / S70×6 / S75×6 | Correct adapter or a proper reducer; never force |
| Cage node cracked | Impact, or a stacked load over rating | Count cracked nodes; check plate stack rating | Do not stack; return for cage swap |
| Tote rocks on the forks | Base weld failed at one corner | Lift 2 in and look at all four welds | Take out of service immediately — transplant job |
| Rust bleeding through the zinc | Galvanising breached, usually at a weld | Wire-brush a test patch | Cosmetic for utility use; fails food-grade intake |
| Label illegible after a season | Direct-print on HDPE in UV | Whether the UN plate is also fading | Stencil and clear-coat, or stainless tag |
Using the container, answered at length.
How do I get the last of the cargo out?
Tip the unit forward slightly so the sump is the low point, and vent the top cap while you drain — most 'the valve is blocked' calls are a vacuum lock, not a blockage. Crack the cap and listen for air.
Expect to leave under a gallon as heel in a standard sump. If recovering that last gallon matters to your economics, ask about units with a dedicated discharge geometry rather than fighting a standard sump.
Can I cut a tote up myself?
People do, for planters and troughs, and it is straightforward with a jigsaw in the plastic and an angle grinder on the cage. Two warnings, both serious.
First, know what was in it: cutting into a bottle that held a solvent is an ignition risk, and never put your head or arm inside an intact container, which is a confined space that has killed people. Second, cut edges on HDPE are sharp and the cage tubes spring when relieved. Our fabricators build sixteen standard designs from Grade C and D stock, finished and deburred, if you would rather not.
What can I do with a tote that failed?
A bottle that cannot be trusted with a regulated cargo can hold rainwater for another fifteen years. Harvesting, planters, troughs, compost tumblers, ballast, erosion control, aquaponics sumps, dust suppression skids — sixteen standard builds, all from donor stock that failed container service.
And if you do not want it, we will collect it and pay for it. A failed unit is still 55 lb of steel at 92% recovery and 42 lb of HDPE at 68%.
Do I need secondary containment?
That is decided by your cargo and your jurisdiction, not by the container, and it is a question for your own environmental people. Where you do need it, size it for the largest single container plus a margin.
The practical trap is that a spill pallet rated for drums is not rated for an IBC. A 275-gallon tote is 2,420 lb of water or 3,637 lb of 50% caustic, concentrated on thirteen square feet.
How long can I leave a cargo sitting in a tote?
The container is usually not the limit — the cargo is. Hypochlorite loses strength continuously and faster when warm. Hydrogen peroxide off-gasses and needs a vent throughout. Vegetable oils oxidise. Latex is finished if it freezes. Glycols and fertilisers are indefinitely stable.
For the container itself: solid cap, valve closed, out of direct sun, filled to 85% if the cargo is water-based and the temperature will drop below freezing. Under those conditions a sound bottle will sit for years without any change we can measure.
Can I store drinking water in a reclaimed tote?
In a rebottled unit, yes — a new HDPE bottle in an inspected cage, with an FDA-compliant EPDM gasket and new closures. For potable water that is the only option we will sell you.
Not in a washed unit, however good the wash. The bottle has a history, and for drinking water the correct answer to 'what was in it before?' is 'nothing'. Keep it out of sunlight, use it within a season, and treat the water as your own responsibility rather than the container's.
Is a tote safe for diesel or heating oil?
The container handles it: HDPE is good with diesel and a Viton gasket is correct — never EPDM, which swells in hydrocarbons. The constraint is almost never the tote.
It is your local fire code, insurer and state environmental rules, which often restrict storing fuel in a non-metallic container, require secondary containment, or cap the volume on site. Check before you buy, because the container will arrive compliant and the installation may not be.
Thirty more terms, including the ones people use loosely.
The glossary page defines sixty-six terms. These are the next thirty, weighted toward the vocabulary that appears in quotes and arguments.
Condition and material
- Crazing — a network of fine branching cracks from chemical and mechanical stress acting together. Absolute disqualifier; never improves.
- Stress whitening — localised opacity where HDPE has been strained, usually a forklift impact at the sump. Not crazing, not automatically a failure.
- Creep — slow permanent deformation under sustained load. Why a hot full tote should never be stacked.
- Environmental stress cracking — cracking under combined stress and a chemical that would harm neither alone. The reason compatibility tables exist.
- Chalking — powdery UV-degraded surface. Cosmetic until it becomes wall loss.
- Ghosting — a faint permanent shadow of a prior cargo visible through the wall. Cosmetic, but it costs a grade.
- Regrind — reprocessed HDPE from our own line, 68% recovery after label and residue loss.
Geometry and handling
- Footprint — the base dimensions, 40 × 48 in on a standard tote. What decides trailer fit.
- Headspace — the deliberately unfilled volume above the cargo. Sixteen percent in winter.
- Heel — the residual cargo left after discharge. Under a gallon is normal; five is a waste job.
- Sump — the recessed low point feeding the valve, and the most common crack location.
- Four-way entry — forks can enter on all four sides. Not universal; ask.
- Superimposed load — the stacking figure on the UN plate.
- Diagonal check — measuring corner to corner to find a cage pushed out of square by impact.
- Node — a welded tube intersection on the cage. 44 to 54 per cage, counted individually.
Closures
- Buttress thread — the asymmetric thread family (S60×6, S70×6, S75×6) that will start on a neighbour and then bind.
- Camlock — quick-connect hose coupling, types A through F plus the DC dust cap.
- Bung — the threaded insert at a port that an adapter seats into.
- Breather valve — a one-way vent for off-gassing cargo such as hypochlorite or peroxide.
- Dip tube — an internal suction tube for pumping. Traps residue; a wash problem.
- Tamper seal — a frangible seal proving the unit has not been opened since despatch.
Commercial and compliance
- Rebottling — fitting a new HDPE bottle into an inspected cage and base. 4,118 units in 2025.
- Take-back — our standing offer to collect and pay for containers at end of use, including reclaim stock.
- Passport — the per-unit record keyed to the cage ID: intake, wash, test, grade, operator, dates. Seven years.
- Prior-contents declaration — the written statement of what was in the unit, from the company that filled it. No declaration, no entry.
- Packing group — the hazard severity band on the UN plate: X covers I–III, Y covers II–III, Z covers III only.
- Periodic test — the 2.5-year leak test and 5-year full inspection that keep a marked unit in regulated service.
- Design type — the approved configuration a UN marking refers to. Properties of the type, not of the individual unit's cleanliness.
- ISPM 15 — the heat-treatment stamp a timber base needs to cross a border.
- Diversion rate — share of intake not landfilled. Meaningless without the residual figure beside it, which is why we publish 94.2% and 4.4% together.
- Avoided emissions — the CO₂e not emitted because a container was reused rather than replaced. Our factors are published in full; we use the end of every range that makes us look worse.
How the container in your yard came to be shaped like that.
The modern caged IBC is a surprisingly young object, and almost every feature of it is the fossil of a specific problem.
Drums and nothing between
Liquids moved in 55-gallon drums or in bulk tankers. Anything in between meant handling dozens of drums, which is why the intermediate category was invented at all.
The first rigid composites
A blow-moulded plastic bottle inside a steel frame, sized to a pallet footprint so a forklift could handle it. The idea has not changed since.
The pallet footprint settles
40 × 48 inches in North America, 1,200 × 1,000 mm in Europe. Every trailer count on this site descends from that choice.
UN performance testing
Packagings began to be approved by design type and performance test rather than by prescription, which is where the 31HA1 marking family comes from.
Periodic testing arrives
The 2.5-year leak test and 5-year inspection cycle formalised, creating the date-stamped plate that decides whether a used unit can still carry a regulated cargo.
Reconditioning becomes a trade
Enough units in circulation, and enough value in a steel cage that outlasts three bottles, for washing and rebottling to be businesses rather than favours.
One bay and a used pressure washer
Re:IBCtote starts in a rented bay in metro Detroit, washing totes for local chemical blenders who could not get a straight answer about prior contents.
Grading gets published
We write down the disqualifiers rather than keeping them in an inspector's head, because the arguments about Grade B were taking more time than the washing.
The passport
Every unit gets a record keyed to its cage ID: intake, wash parameters, test results, grade, operator, dates. Seven-year retention, reissuable years later.
38,210 containers
Our largest year: 94.2% diverted, 4.4% residual published rather than rounded away, 4,281 tonnes of CO₂e avoided on factors we publish in full.
The same containers, different weather.
“Half the people who ask us for food-grade are about to put site water in it. Telling them so costs us a third of the invoice and earns the next four orders.”
Send us the cargo, not the grade.
Tell us what is going in the container and what you are doing with it, and we will name the grade, say what would disqualify a unit from it, and tell you if something cheaper does the job. That last part is why people come back.